2009-2010Catalog By September 2008

These saws are designed for general sizing and cutting of natural woods.  A higher number of teeth provides a finer edge to the cut, but should be used only on thinner material. The saw blades designated by the prefix GAM contain Micro-Sheen C-4 sub-micron carbide, which provides longer tool life. The blades designated by the prefix GAL have laser cuts in the body to help reduce noise.
DIAMETERR TEETH DESIGN KERF PLATE BORE HOOK ORDER  ID 
7 1/4” 24T ATB .110” .079” 5/8” 20 RS72524
7 1/4” 40T ATB .110” .079” 5/8” 10 GA72540
7 1/4” 60T ATB .110” .079” 5/8” 10 GA72560
8” 40T ATB .118” .079” 5/8” 10 GA840
8” 60T ATB .118” .079” 5/8” 10 GA860
9” 40T ATB .126” .087” 5/8” 10 GA940
9” 60T ATB .126” .087” 5/8” 10 GA960
10” 40T ATB .126” .087” 5/8” 10 GA1040
10” 40T ATB .126” .087” 5/8” 10 GAL1040*
10” 60T ATB .126” .087” 5/8” 10 GA1060
10” 60T ATB .126” .087” 5/8” 10 GAM1060**
10” 60T ATB .126” .087” 5/8” 10 GAL1060*
10” 80T ATB .126” .087” 5/8” 10 GA1080
10” 80T ATB .126” .087” 5/8” 10 GAM1080**
10” 80T ATB .126” .087” 5/8” 10 GAL1080*
10” 100T ATB .126” .087” 5/8” 10 GA1010
250mm 60T ATB 3.2mm 2.2mm 30mm/2 PH 10 GAM2503060**
300mm 72T ATB 3.2mm 2.2mm 30mm/2+2 PH 10 GAM3003072**
300mm 96T ATB 3.2mm 2.2mm 30mm/2+2PH 10 GAM3003096**
12” 48T ATB .134” .094” 1” 10 GA1248
12” 60T ATB .134” .094” 1” 10 GA1260
12” 80T ATB .134” .094” 1” 10 GA1280
12” 80T ATB .134” .094” 5/8” 10 GA1280P
12” 80T ATB .134” .094” 1” 10 GAL1280*
12” 80T ATB .165” .118” 1” 10 GA1280CW
12” 100T ATB .126” .087” 1” 10 TS1210
350mm 72T ATB 3.5mm 2.5mm 30mm 10 GAM3503072
14” 40T ATB .184” .134” 1” 0 GA1440
14” 60T ATB .157” .118” 1” 10 GA1460
14” 60T ATB .157” .118” 1” 10 GAL1460*
14” 80T ATB .157” .118” 1” 10 GA1480
14” 80T ATB .157” .118” 1” 10 GAL1480*
14” 100T ATB .157” .118” 1” 10 GA1410
14” 120T ATB .165” .118” 1” 10 GA1412
400mm 120T ATB 4.6mm 3.4mm 30mm 10 GA4003012
16” 40T ATB .185” .134” 1” 10 GA1640
16” 60T ATB .165” .126” 1” 10 GA1660
16” 80T ATB .165” .126” 1” 10 GA1680
16” 100T ATB .165” .126” 1” 10 GA1610
18” 40T ATB .180” .134” 1” 10 GA1840
18” 60T ATB .180” .134” 1” 10 GA1860
18” 80T ATB .180” .134” 1” 10 GA1880
18” 100T ATB .180” .134” 1” 10 GA1810
18” 120T ATB .180” .134” 1” 10 GA1812
18” 140T ATB .180” .134” 1” 10 GA1814
20” 40T ATB .194” .134” 1” 10 GA2040
20” 60T ATB .180” .134” 1” 10 GA2060
20” 80T ATB .180” .134” 1” 10 GA2080
20” 100T ATB .180” .134” 1” 10 GA2010
20” 120T ATB .180” .134” 1” 10 GA2012
500mm 120T ATB 5.0mm 3.5mm 30mm/2 PH 10 GA5003012
500mm 144T ATB 5.0mm 3.5mm 30mm/2 PH 10 GA50030144
500mm 120T ATB 5.0mm 3.5mm 70mm/6 PH 10 GA5007012
500mm 96T ATB 5.0mm 3.5mm 70mm/6 PH 10 GA5007096
520mm 144T ATB 5.0mm 3.5mm 30mm/2 PH 10 GA52030144
600mm 144T ATB 5.0mm 3.5mm 30mm/2 PH 10 GA60030144
26” 80T ATB .245” .165” 1” 5 GA2680A
26” 100T ATB .245” .165” 1” 5 GA2610A

*GAL blades have laser slits in the body for noise and vibration control.   **GAM blades use Micro-Sheen C-4 sub-micron carbide for extended tool life.
These 500mm, 520mm, and 600mm are for the Grecon and Paul optimizing up cut saws.